Dc power supply. Read online or download PDF. GW Instek GPD-4303S User Manual. Manuals Directory ManualsDir.com - online owner manuals library. GW Instek manuals. GW INSTEK PART NO. ISO-9001 CERTIFIED MANUFACTURER. The SPD-3606 DC power supply provides 375W output capacity, three isolated outputs with dual-range for CH1 & CH2, highly efficient power conversion, low noise, high reliability, thorough protection,excellent value, and a compact size. GW Instek SPD-3606 User Manual. Related Products. Siglent SPD3303C: Programmable Linear DC Power Supply. DC Power Supply SPD-3606 USER MANUAL GW INSTEK PART NO. 82PD-36060M0 ISO-9001 CERTIFIED MANUFACTURER Toll Free 1-800-5 This manual contains proprietary information, which is protected. SPD-3606 provides Output on/off function. User can preset the voltage/current value and check the connection between DUT and power supply is ready. Then users could control output on/off by manual switching or by remote connection. SPD-3606 also provides volume guard function.
Advertising
SAFETY
INSTRUCTION
7
•
To ensure fire protection, replace the fuse only
with the specified type and rating.
with the specified type and rating.
•
Disconnect the power cord before fuse
replacement.
replacement.
•
Make sure the cause of fuse blowout is fixed
before fuse replacement.
before fuse replacement.
Cleaning SPD-
3606
3606
![Spd-3606 Spd-3606](https://unimaxsupply.com/equip/powersup/instek1z400x.jpg)
Disconnect the power cord before cleaning.
•
Use a soft cloth dampened in a solution of mild
detergent and water. Do not spray any liquid.
detergent and water. Do not spray any liquid.
•
Do not use chemical or cleaner containing harsh
material such as benzene, toluene, xylene, and
acetone.
material such as benzene, toluene, xylene, and
acetone.
Operation
Environment
Environment
•
Location: Indoor, no direct sunlight, dust free,
almost non-conductive pollution (Note below)
almost non-conductive pollution (Note below)
•
Relative Humidity: < 80%
•
Altitude: < 2000m
•
Temperature: 0°C to 40°C
(Pollution Degree) EN 61010-1:2001 specifies the pollution degrees
and their requirements as follows. SPD-3606 falls under degree 2.
and their requirements as follows. SPD-3606 falls under degree 2.
Pollution refers to “addition of foreign matter, solid, liquid, or
gaseous (ionized gases), that may produce a reduction of dielectric
strength or surface resistivity”.
gaseous (ionized gases), that may produce a reduction of dielectric
strength or surface resistivity”.
• Pollution degree 1: No pollution or only dry, non-conductive
Gw Instek Website
pollution occurs. The pollution has no influence.
• Pollution degree 2: Normally only non-conductive pollution
occurs. Occasionally, however, a temporary conductivity caused
by condensation must be expected.
by condensation must be expected.
• Pollution degree 3: Conductive pollution occurs, or dry, non-
conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.
Storage
environment
environment
•
Location: Indoor
•
Relative Humidity: < 70%
•
Temperature: −10°C to 70°C
SPD-3606 User Manual
8
Power cord for the United Kingdom
When using SPD-3606 in the United Kingdom, make sure the power
cord meets the following safety instructions.
cord meets the following safety instructions.
NOTE: This lead/appliance must only be wired by competent persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with
the following code:
Green/ Yellow:
the following code:
Green/ Yellow:
Earth
Blue: Neutral
Brown: Live
Brown: Live
Download game mini pets for android. (Phase)
As the colours of the wires in main leads may not correspond with the
colours marking identified in your plug/appliance, proceed as follows:
The wire which is coloured Green & Yellow must be connected to the
Earth terminal marked with the letter E or by the earth symbol or
coloured Green or Green & Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the terminal
marked with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment or
contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, cable of
0.75mm
colours marking identified in your plug/appliance, proceed as follows:
The wire which is coloured Green & Yellow must be connected to the
Earth terminal marked with the letter E or by the earth symbol or
coloured Green or Green & Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the terminal
marked with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment or
contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, cable of
0.75mm
2
should be protected by a 3A or 5A fuse. Larger conductors
Gw Instek Gpt 9804 Manual
would normally require 13A types, depending on the connection
method used.
Any moulded mains connector that requires removal /replacement
must be destroyed by removal of any fuse & fuse carrier and disposed
of immediately, as a plug with bared wires is hazardous if a engaged in
live socket. Any re-wiring must be carried out in accordance with the
information detailed on this label.
method used.
Any moulded mains connector that requires removal /replacement
must be destroyed by removal of any fuse & fuse carrier and disposed
of immediately, as a plug with bared wires is hazardous if a engaged in
live socket. Any re-wiring must be carried out in accordance with the
information detailed on this label.
Advertising
Gw Instek Power Supply
Popular Brands
Gw Instek Spd-3606
Popular manuals